JT&T Products

JT&T's Silicone Rubber Tape is an improved wrapping tape extruded of high performance silicone rubber suitable wherever a tough, permanently resilient, void-free insulation is required.The silicone rubber tape is self-adhering and self-fusing, curing in 24 hours at room temperature. Faster curing and a harder finish can be accomplished through the application of heat after wrapping.Temperature range is -60 to 200 for continuous use; -65 to 260 for intermittent use.The tape meets or exceeds the...

Heat Shrink Solder Seal terminals feature a band of low melt solder in the middle of heat shrink. They allow you to solder and shrink in one step. Note these terminals do not crimp on and are solder only. If you would like the crimp as well, consider the Crimp & Solder Seal Terminals. JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after crimping. JT&T's...

⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel. ⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

Crimp and Solder Seal terminals feature a band of solder above the connection. After crimping normally, apply heat to activate the heat shrink. The low melt solder will flow into the connection. This provides the best possible connection - no loss of conductivity and is stronger than the wires themselves. JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after...

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel.⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

Crimp and Solder Seal terminals feature a band of solder above the connection. After crimping normally, apply heat to activate the heat shrink. The low melt solder will flow into the connection. This provides the best possible connection - no loss of conductivity and is stronger than the wires themselves. JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after...

Crimp and Solder Seal terminals feature a band of solder above the connection. After crimping normally, apply heat to activate the heat shrink. The low melt solder will flow into the connection. This provides the best possible connection - no loss of conductivity and is stronger than the wires themselves. JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after...

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel. ⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel. ⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel.⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

High Temperature terminals feature a continuous operating temperature rating of 900F / 482C. Constructed of nickel plated steel. ⚠ WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

JT&T Products offers a full line of non-insulated & insulated terminals made from vinyl (P.V.C), nylon & heat shrink.

Tapers to a .090" width. Used to release larger terminals including Maxi fuse terminals. Also opens secondary locking devices on connector housings. Used to release most GM, Ford & Chrysler OEM terminals from their insulated housing. Can be used as an OEM#12150860 &/or OEM#12094441 tool.

This tool is designed for crimping open barrel 18, 16 and 14 gauge terminals found on Weather Packs, Deutsch DT/Amphenol AT stamped terminals, and some Molex type terminals. This tool also performs a starter crimp on 20 thru 12 gauge wire. ? WARNING: Cancer and reproductive harm - www.p65warnings.ca.gov

The Weather-Pack Extractor Tool is designed for extracting weather-pack terminals from their connector housing for servicing and replacement. Designed solely to depress Weather Pack terminal retention barbs to allow terminal removal from tower or shroud. Equivalent to: Delphi/Packard OEM#12014012 & SPX Kent Moore J-38125-10A.

Tapers to a .035" width. Used to release 150 Metri-Pack, 280 Metri-Pack, 280 Tangless, 280 Bus Bar, 630 Pull to Seat, GT 150, GT 280, Wedge Base lamp socket terminals, and Indexing Candelabra Bayonet Double Contact Lamp Socket Terminals. Used to release most GM, Ford & Chrysler OEM terminals from their insulated housing.This tool has the smallest flat blade available. Equivalent to Green Handle Delphi/Packard OEM#12094429 and SPX Kent Moore J-38125-12A Also replaces Delphi/Packard...

JT&T's 2 to 1 Single/Thin Wall Cross-Linked Polyolefin Heat Shrink Tubing is irradiated, flexible & intended for general purpose applications requiring recognition by military & industrial specifications.  UL recognized, CSA certified, RoHS compliant & ABS approved.  Meets requirements of SAE-AMS-DTL-23053/5 (formerly MIL-I-23053/5, MIL-DTL-23053/5), Classes 1, 2 (Clear), 3. It is single-wall, flame-retardant, mechanically strong &...

Heat Shrink Solder Seal terminals feature a band of low melt solder in the middle of heat shrink. They allow you to solder and shrink in one step. Note these terminals do not crimp on and are solder only. If you would like the crimp as well, consider the Crimp & Solder Seal Terminals. JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after crimping. JT&T's...

JT&T's 2 to 1 Single/Thin Wall Cross-Linked Polyolefin Heat Shrink Tubing is irradiated, flexible & intended for general purpose applications requiring recognition by military & industrial specifications.  UL recognized, CSA certified, RoHS compliant & ABS approved.  Meets requirements of SAE-AMS-DTL-23053/5 (formerly MIL-I-23053/5, MIL-DTL-23053/5), Classes 1, 2 (Clear), 3. It is single-wall, flame-retardant, mechanically strong &...

JT&T's 2 to 1 Single/Thin Wall Cross-Linked Polyolefin Heat Shrink Tubing is irradiated, flexible & intended for general purpose applications requiring recognition by military & industrial specifications.  UL recognized, CSA certified, RoHS compliant & ABS approved.  Meets requirements of SAE-AMS-DTL-23053/5 (formerly MIL-I-23053/5, MIL-DTL-23053/5), Classes 1, 2 (Clear), 3. It is single-wall, flame-retardant, mechanically strong & will not melt or split when...

JT&T's Heat Shrink Terminals have been adhesive-lined to seal the connection. The translucent tubing allows for visual inspection. Terminals provide maximum contact and tensile strength after crimping. JT&T's terminals are constructed from pure copper (Alloy 110), annealed & electro tin plated. Electro Tin plating provides exceptional corrosion resistance. Insulator sleeve is color-coded for wire size and identification. JT&T Products offers a full line of terminals made from vinyl (P.V.C),...